Bosch Qv60-rgc1 Manual [extra Quality]
: Built-in safeguards include short-circuit-proof output lines, open-circuit cable break detection for feedback sensors, and a low voltage ( ) auto-fault trigger. Terminal Assignments and Block Pinouts
Installation Note: If the cable runs between your DC power system supply infrastructure and the card rack exceed 1 meter, separate your Control Zero line ( b12 ) from your main Power Ground ( b2 ). Route them independently back to your main system earth termination point to avoid ground loops. Commissioning & Trimming Potentiometers
Because this is a legacy product, Bosch Rexroth maintains digital archives. You can search for the full technical data sheet and installation instructions using the material number 0811405104 official Bosch Rexroth Manuals portal potentiometer adjustment settings for your current setup? PV45 0 811 405 096 Amplifier Card Bosch Manual 1 PDF
| Parameter | Value | Unit | Notes | | :--- | :--- | :--- | :--- | | | 100 × 160 × 35 | mm | Standard Eurocard size. | | Connector Type | DIN 41 612 – F32 | - | Industry-standard 32-pin connector. | | Ambient Temp. | 0 to +70 | °C | Operating temperature range. | | Storage Temp. | –20 to +70 | °C | Temperature range for storage. | | Supply Voltage (Vcc) | 24 | V DC | Nominal operating voltage. | | Power Consumption | max. 35 / 60 | W | Depends on load. | | Current Consumption | max. 1.5 / 2.5 | A | Depends on load. | | Valve Solenoid Current | 2.7 / 3.7 | A | Maximum current the card can supply to the valve coil. | | Command Signals | 0 to +10 | V DC | Standard setpoint voltage from the machine’s PLC. | | Signal Source Impedance | 1 | kΩ | For connecting an external potentiometer. | | Max. Cable Length (Valve) | 20 (1.5 mm²) / 50 (2.5 mm²) | m | Maximum distance to the valve, depending on wire gauge. | | Max. Cable Length (Feedback) | max. 50 | m | Maximum distance for position feedback sensor wiring. | bosch qv60-rgc1 manual
: If your rectified AC power source has a ripple effect exceeding 10%, the manual dictates installing a separate, external smoothing capacitor bridged across pins b28/b30 and b2/b4 .
| Indicator Light | Meaning | Solution | |----------------|----------------------------|-------------------------------------------| | Red + beep x2 | Low battery | Return to dock manually. | | Red + beep x3 | Brush jammed | Clean roller brush and remove hair/debris.| | Red + beep x4 | Cliff sensor error | Clean sensors; move away from dark floors.| | Flashing orange| Filter full/dirty | Clean or replace the filter. |
The front panel of the QV60-RGC1 features multi-turn trimming potentiometers (pots) and status LEDs. Follow this sequential commissioning workflow to tune the card: Commissioning & Trimming Potentiometers Because this is a
Proper maintenance and adherence to safety practices will prolong the life of the QV60-RGC1 and the system it controls.
Inputs for command values (0 to +6 V, 0 to +9 V, or 0 to +10 V).
This comprehensive technical guide serves as a manual overview. It details the product specifications, installation steps, adjustment procedures, and troubleshooting protocols for engineering teams managing industrial machinery. Technical Specifications | | Connector Type | DIN 41 612
If you are currently servicing a machine utilizing this card, you can reference further platform documentation on the Bosch Rexroth Germany Manual Portal or the Bosch Rexroth US Manual Hub using material index number . BOSCH QV60-RGC1 0 811 405 104 VALVE AMPLIFIER CARD
card has several adjustment potentiometers accessible on the front panel, allowing for fine-tuning without removing the card from the rack. 4.1 Front Panel Potentiometers